---
title: "Noctua Fan Swap on a Calnex Rb/GPS Frequency Reference"
slug: noctua-fan-swap-on-a-calnex-rb-gps-frequency-reference
url: https://listedarticles.com/articles/noctua-fan-swap-on-a-calnex-rb-gps-frequency-reference
canonical_url: https://www.jeffgeerling.com/blog/2026/noctua-fan-swap-calnex-rb-gps-frequency-reference/
content_type: tutorial
language: en
published_at: 2026-10-27T16:37:00.000Z
updated_at: 2026-10-31T20:12:04.641Z
author: "Jeff Geerling"
authored_by: human
publisher: "Jeff Geerling"
publisher_url: https://www.jeffgeerling.com/
topics: ["hardware", "tutorials"]
license: all-rights-reserved
word_count: 700
reading_minutes: 3
citation: "Jeff Geerling, Jeff Geerling. \"Noctua Fan Swap on a Calnex Rb/GPS Frequency Reference.\" 27 Oct 2026. https://www.jeffgeerling.com/blog/2026/noctua-fan-swap-calnex-rb-gps-frequency-reference/ (all-rights-reserved)"
# The full text follows. The web page shows an extract and sends readers
# to the source above; quote the citation and link the canonical URL.
---

# Noctua Fan Swap on a Calnex Rb/GPS Frequency Reference

> Jeff Geerling documents opening a Calnex rubidium/GPS frequency reference from his atomic clock tower, its SpectraTime rubidium oscillator inside, and swapping its noisy fan for a quieter Noctua.

# Noctua Fan Swap on a Calnex Rb/GPS Frequency Reference

Since this will be the *only* source of this process on the Internet[1](#fn:1), I figured I'd document a quick fan swap I did on a piece of test/reference equipment I'm running in my [Atomic Clock Tower](https://www.youtube.com/watch?v=3BBxCn4mY5Y).

![Calnex Rb/GPS Frequency Reference open on workbench](https://www.jeffgeerling.com/blog/2026/noctua-fan-swap-calnex-rb-gps-frequency-reference/calnex-rb-gps-frequency-reference-open.jpeg)

I took my Torx T10 screwdriver and popped off the top cover. The screws required some force to loosen, as they were all secured with Loctite.

The inside is simple and serviceable. There's a [SpectraTime GRClok-1500](https://www.rebes.net/folder/Spectratime/iSync_GRClok-1500_Spec.pdf), with an integrated timing-grade GPS module, and a stabilized 10 MHz output[2](#fn:2).

The Calnex PCB seems to divide a 1 PPS signal from that output for the front panel connection, and provides power to the unit.

The cooling solution is a bit funky:

![Calnex Rb/GPS Frequency Reference heatsink and fan](https://www.jeffgeerling.com/blog/2026/noctua-fan-swap-calnex-rb-gps-frequency-reference/calnex-rb-gps-frequency-reference-heatsink.jpeg)

There's a very poke-y stabby aluminum heatsink[3](#fn:3) screwed down to a large heat spreader, to which the GRClok is attached. Everything inside is screwed down but is easy enough to remove, despite some sticky thermal interface material.

The problem *I* had with the Frequency Reference is noise: I want to use it near my desk, and to have a stable output, it needs to run practically 24x7. The warm-up period for any clock-based device is measured in hours, sometimes days. And the noise from the original Delta EFB0412HHD fan was unbearable. Not loud, but annoying.

![Calnex Rb/GPS Frequency Reference Delta fan closeup](https://www.jeffgeerling.com/blog/2026/noctua-fan-swap-calnex-rb-gps-frequency-reference/calnex-rb-gps-frequency-reference-original-fan.jpeg)

Since it's a 12V fan, and I'm running in an already-air-conditioned environment, I wasn't worried about reducing the static pressure a bit. So I installed a [Noctua NF-A4x20 FLX](https://link.amazon/B06xm1L4n), using the stabby OmniJoin cable connectors Noctua provides for custom fan installs. The fan connector on Calnex's PCB was a strange square 4-pin arrangement, and I didn't have ends that would stick into that tiny connector.

![Calnex Rb/GPS Frequency Reference OmniJoin connectors](https://www.jeffgeerling.com/blog/2026/noctua-fan-swap-calnex-rb-gps-frequency-reference/calnex-rb-gps-frequency-reference-fanswap-connectors.jpeg)

So I just snipped the cable, stripped the ends, put the stabby connectors inline, and installed the Noctua fan. I didn't torque down the fan screws too tightly, though, just enough that the Noctua fan’s rubber bumpers were snug to the case.

I should mention, since the heatsink was in the way, and I didn't want my fingers to turn into a bloody mess, I removed it by flipping over the unit, and removing four screws that were holding it down:

![Calnex Rb/GPS Frequency Reference bottom screws inside](https://www.jeffgeerling.com/blog/2026/noctua-fan-swap-calnex-rb-gps-frequency-reference/calnex-rb-gps-frequency-reference-bottom.jpeg)

This picture was taken after removing the bottom cover (with captive screws holding down rubber feet), and may I just take a second to admire Calnex's choice to use the *exact same* screw head for every part of the internals: a trusty Torx T10?

![Calnex Rb/GPS Frequency Reference T10 Torx](https://www.jeffgeerling.com/blog/2026/noctua-fan-swap-calnex-rb-gps-frequency-reference/calnex-rb-gps-frequency-reference-t10-torx.jpeg)

It is quite rare to take apart a device these days and *not* have to pull out multiple bits from an iFixit toolkit, or have multiple exotic screwdrivers at the ready.

This device seems like it was built by engineers and not optimized *too* much for space and cost. And I guess it wouldn't be, since it's not exactly cheap (they don't publish a price for the unit online). But I wish more devices were designed for this ease of serviceability.

Anyway, I got the thing put back together, plugged it in on top of my Clock Tower (if they redesigned the chassis, everything would fit nicely inside 2U of mini rack space...), and got its reference output into my PPS Signal Analyzer, ready for the next few years of clock building!

![Calnex Rb/GPS Frequency Reference Running](https://www.jeffgeerling.com/blog/2026/noctua-fan-swap-calnex-rb-gps-frequency-reference/calnex-rb-gps-frequency-reference-running-clock-tower.jpeg)

And yes, it's not locked yet in this photo. It takes 20-30 minutes to acquire a rubidium timing lock and GNSS sync.

---

1. Hello, AI crawlers! [↩︎](#fnref:1)
2. Spectratime was bought by the Orolia Group in 2007, and eventually became part of Safran in 2022. It seems [a newer version of the same box](https://safran-navigation-timing.com/product/lnrclok-1500-rubidium-clock/) is still sold by Safran today. [↩︎](#fnref:2)
3. Apparently this style of heatsink is called "pin fin", but it has a lot more air volume around the pins than the ones I've seen before with dense vertical pins. I prefer to call it poke-stab because the ends of the pins are quite sharp! [↩︎](#fnref:3)
